400A Pole Mounted Fused Cut-out

This pole mountable fused Cut-out is the ideal method of providing rural dwellings with a safe, protective and reliable Low Voltage power supply.

Request a Quote

Overview

Other electrical products

400A Pole Mounted Fused Cut-out for Project Requirements

400A Pole Mounted Fused Cut-out is a supplier-listed electrical accessory or protection component. The authenticated product source below is retained as the technical starting point; confirm the exact variant and installation requirements before ordering.

Product category: Electrical component
Model reference: 400A Pole Mounted Fused Cut-out
Technical data: Source-specific
Final selection: Confirm by drawing

Use the exact target product source and approved project documents for final selection. Ratings, dimensions, compatibility, material and applicable standards remain subject to technical review where not published.

Request a configuration review Browse other products

Published product data

400A Pole Mounted Fused Cut-out Source Details

The block below preserves information published on the target product listing. It is a starting point for engineering review, not a substitute for an approved project drawing.

Published source notes

Product Features

◆Each fused Cut-out has fuse contacts and cable terminal plates which are manufactured from bronze with tin coating.

◆These plates incorporate M12 captive studs with nuts and washers for the reception of cable sockets (lugs) up to 300mm2 (compression type only at 300mm2）with copper or aluminium conductors.

◆For ease of mounting to either a wall or a wooden pole, the fused Cut-out is supplied with an M12 coach screw.

◆For cross-arm type mounting the Fused Cut-out can be supplied with an M12 nut, bolt and washer.

Fuse link

◆This fused cut-out is designed to accommodate standard-wedge type fuse link to BS88 Part 5.Tested and approved for category of duty 415AC80.

◆Fixing center requirement is 82mm.

◆Standard fuse link rating range from 20A to 400A.

Pin type insulator

Model	Fixing Arrangement
FRT-PL01	For wall or pole mounting:c/w M12 coach screw
FRT-PL02	For cross-arm mounting:c/w M12 nut,nolt and washer
FRT-PL-WFL	Spare fuse link

Note: Stepped washers recommended if lug palm has hole 16mm or greater.

Confirm the exact model, unit, test condition and drawing revision before placing an order. Do not transfer a value or interface from a similar-looking product.

Selection checklist

Specify the Product for Its Intended Duty

Define the product function. State the equipment it connects to and the protection, switching, indication or accessory role required.
Confirm electrical compatibility. Provide the system voltage, current, frequency, insulation level and any short-circuit duty that applies.
Check the mechanical interface. Confirm mounting position, terminal or fitting interface, dimensions, cable connection and enclosure requirements.
Describe the service environment. State indoor or outdoor location, pollution, temperature, altitude, humidity and corrosion conditions.
List documents and quantity. Include drawings, marking, packing, destination market and required project documents in the RFQ.

Configuration and supply boundary

Review the 400A Pole Mounted Fused Cut-out Configuration

This listing may cover a product family or project-specific configuration. State the exact requested function and interface so the quotation does not mix similar accessories or protection components.

Electrical fit

Confirm system parameters, insulation coordination, control or indication circuit requirements and any protection duty.

Mechanical fit

Specify mounting, terminals, hardware, dimensions and compatibility with the connected equipment.

Environment and documents

State installation conditions, required drawings, test evidence, marking and destination-market requirements.

Commercial boundary

Quantity, packing, delivery schedule, private label and project documents depend on technical review and quotation.

Company scale

Fuerte at a Glance

FUERTE lists 1985 as its founding year, 220+ employees and a 36,000 m² built-up area. These supplier-published figures provide context for manufacturing and project support.

1985

Founded in

Supplier-published company history

220+

Employees

Published workforce scale

36,000 m²

Built-up area

Published manufacturing footprint

OEM

& ODM support

Subject to technical review

OEM & ODM capability

Custom Support for Electrical-Component Projects

FUERTE’s published OEM and ODM scope includes voltage/current adaptation, mounting hardware, nameplates, packaging and shipping marks.

Product configurationReview function, system compatibility, service conditions and project-specific requirements.
Mechanical interfaceConfirm fittings, mounting dimensions, terminals and equipment interface.
Project documentationState drawings, marking, packing, shipping marks and acceptance-document requirements before quotation.

Frequently asked questions

400A Pole Mounted Fused Cut-out FAQ

What should be confirmed first?

Start with the product function, system compatibility, electrical duty, installation interface and service environment.

Can data be borrowed from a similar product?

No. Confirm the exact target model and approved drawing before using a rating, dimension or interface in a purchase specification.

Can fittings, marking or packing be reviewed?

FUERTE publishes adaptation of mounting hardware and project specifications as an OEM/ODM scope. Availability depends on technical review.

What should be included in a quote request?

State the product function, compatible equipment, drawings, ratings, interface, quantity, destination and required documents.

Configuration review

Send the 400A Pole Mounted Fused Cut-out Requirements

Provide the product function, system conditions, interface, drawings, quantity, destination market and required documents.

Go to the quote form

Request a Custom Quote

Interested in this product? Fill out the form below and our sales team will get back to you within 24 hours.

Other Products